Switch to SpeakEasy.net DSL

The Modular Manual Browser

Home Page
Manual: (OpenBSD-5.7)
Apropos / Subsearch:
optional field

ACCEPT(2)                   BSD System Calls Manual                  ACCEPT(2)

     accept, accept4 -- accept a connection on a socket

     #include <&lt;sys/socket.h>&gt;

     accept(int s, struct sockaddr *addr, socklen_t *addrlen);

     accept4(int s, struct sockaddr *addr, socklen_t *addrlen, int flags);

     The argument s is a socket that has been created with socket(2), bound to
     an address with bind(2), and is listening for connections after a
     listen(2).  The accept() call extracts the first connection request on
     the queue of pending connections, creates a new socket with the same non-
     blocking I/O mode as s, and allocates a new file descriptor for the
     socket with the close-on-exec flag clear.

     The accept4() system call is similar, however the non-blocking I/O mode
     of the new socket is determined by the SOCK_NONBLOCK flag in the flags
     argument and the close-on-exec flag on the new file descriptor is deter-
     mined by the SOCK_CLOEXEC flag in the flags argument.

     If no pending connections are present on the queue, and the socket is not
     marked as non-blocking, accept() blocks the caller until a connection is
     present.  If the socket is marked non-blocking and no pending connections
     are present on the queue, accept() returns an error as described below.
     The accepted socket may not be used to accept more connections.  The
     original socket s remains open.

     The argument addr is a result parameter that is filled in with the
     address of the connecting entity as known to the communications layer.
     The exact format of the addr parameter is determined by the domain in
     which the communication is occurring.  The structure sockaddr_storage
     exists for greater portability.  It is large enough to hold any of the
     types that may be returned in the addr parameter.

     The addrlen is a value-result parameter; it should initially contain the
     amount of space pointed to by addr; on return it will contain the actual
     length (in bytes) of the address returned.  If addrlen does not point to
     enough space to hold the entire socket address, the result will be trun-
     cated to the initial value of addrlen (in bytes).  This call is used with
     connection-based socket types, currently with SOCK_STREAM.

     It is possible to select(2) or poll(2) a socket for the purposes of doing
     an accept() by selecting it for read.

     The call returns -1 on error.  If it succeeds, it returns a non-negative
     integer that is a descriptor for the accepted socket.

     The following code uses struct sockaddr_storage to allocate enough space
     for the returned address:

           #include <sys/types.h>
           #include <sys/socket.h>

           struct sockaddr_storage addr;
           socklen_t len = sizeof(addr);
           int retcode;

           retcode = accept(s, (struct sockaddr *)&addr, &len);
           if (retcode == -1)
                   err(1, "accept");

     accept() and accept4() will fail if:

     [EBADF]            The descriptor is invalid.

     [ENOTSOCK]         The descriptor doesn't reference a socket.

     [EOPNOTSUPP]       The referenced socket is not of type SOCK_STREAM.

     [EINTR]            A signal was caught before a connection arrived.

     [EINVAL]           The referenced socket is not listening for connections
                        (that is, listen(2) has not yet been called).

     [EFAULT]           The addr or addrlen parameter is not in a valid part
                        of the process address space.

     [EWOULDBLOCK]      The socket is marked non-blocking and no connections
                        are present to be accepted.

     [EMFILE]           The per-process descriptor table is full.

     [ENFILE]           The system file table is full.

     [ECONNABORTED]     A connection has been aborted.

     In addition, accept4() will fail if

     [EINVAL]           flags is invalid.

     bind(2), connect(2), listen(2), poll(2), select(2), socket(2)

     The accept() function conforms to IEEE Std 1003.1-2008 (``POSIX.1'').
     The accept4() function is expected to conform to a future revision of
     that standard.

     The accept() system call first appeared in 4.1cBSD and accept4() in
     OpenBSD 5.7.

     When EMFILE or ENFILE is returned, new connections are neither dequeued
     nor discarded.  Thus considerable care is required in select(2) and
     poll(2) loops.

BSD                            September 9, 2014                           BSD